BNTBV - STAY CLEAN PASTE FLUX
- MSDS: BNTBV
- Manufacturer: J W HARRIS CO INC
- Product Name: STAY CLEAN PASTE FLUX
- National Stock Number: 3439-00-220-3826
Product Identification
Product ID:STAY CLEAN PASTE FLUX
MSDS Date:03/11/1992
FSC:3439
NIIN:00-220-3826
MSDS Number: BNTBV
Responsible Party
CINCINNATI, OH 45242-4110
US
Emergency Phone: 513-891-2000
Info Phone: 513-891-2000;800-543-4536
Cage: FO309
Contractor
Telephone: 513-891-2000
Cage: 27911
Ingredients
ZINC CHLORIDE (SARA III)
CAS: 7646-85-7
RTECS: ZH1400000
Fraction By Weight: 25%
OSHA PEL 1 MG/M3/2 STEL
ACGIH TLV: 1 MG/M3/2STEL FUME93
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:DERMATITIS, HEADACHE, IRRITATION OF
NOSE & THROAT, HOARSENESS. POTENTIALLY HAZARDOUS MATERIALS MAY BE
EMPLOYED IN BASE METALS, FUMES, COATINGS & FILLER METALS USED IN
SOLDERING, BRAZING AND WELDING OR MAY BE RELEASED TO ATMOSPHERE
DURING OPERATIONS.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYE:FLUSH WITH WATER FOR AT LEAST 15 MINUTES. CALL MD.
INHAL:MOVE TO WELL VENTILATED AREA. CALL MD. SKIN:FLUSH WITH
COPIOUS AMOUNTS OF WATER. CALL MD . INGEST:CALL MD IMMEDIATELY .
Fire Fighting
Flash Point Method:OC
Flash Point:490F,254C
Extinguishing Media:DRY POWDER OR CO*2.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT . INORGANIC SALT COMPOSITION PRECLUDES
COMBUSTION OF HYDROGEN.
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.
Accidental Release
Spill Release Procedures:WASH AND SCRUB WITH HOT WATER AND SOAP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE BELOW 100F TO PREVENT
SEPARATION.
Other Precautions:WELDING ARC OR TORCH FLAME MAY BE A SOURCE OF
IGNITION OF COMBUSTIBLE PRODUCT. REFER TO USA STANDARD ANSI/ASC
Z49.1, 1983 "SAFETY IN WELDING & CUTTING" FOR SPECIFIC PRECAUTIONS
IN ALL PHASES OF WELDIN G, CUTTING AND BRAZING.
Exposure Controls
Respiratory Protection:NIOSH/MSHA APPROVED FUME RESPIRATOR OR AIR LINE
RESPIRATOR FOR CONFINED SPACES OR WHERE EXPOSURES ARE ABOVE TLV.
Ventilation:LOC EXHST:REQ IN SEMI-OPEN OR POORLY VENT SPACES. SEE
ANSI/ASC Z49/1-SECTION 5. MECH (GEN):REQ IN SEMI-OPEN OR (SUPDAT)
Protective Gloves:WELDERS PROTECTIVE GLOVES.
Eye Protection:CHEM WORK GOGG &/OR WELDING (SUPP DATA)
Other Protective Equipment:APPROPRIATE CLOTHING FOR PROTECTION AGAINST
SPARKS OR HOT METAL.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
VENT:OR POORLY VENTILATED SPACES. SEE ANSI/ASC Z49.1 SECTION 5. EYE
PROT:HELMET WITH APPROPRIATE SHADED LENS (SEE ANSI/ASC Z49.1
SECTION 4).
Chemical Properties
Spec Gravity:1.02 (H*2O=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:PETROLEUM APPEARANCE AND ODOR
Percent Volatiles by Volume:8
Stability
Stability Indicator/Materials to Avoid:YES
FLUX IS MILDLY CORROSIVE BY NATURE. AVOID CONTACT WITH OTHER MATERIALS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.
Disposal
Waste Disposal Methods:SEND TO LANDFILL IN CLOSED CONTAINERS. SOLID
RESIDUE WASTE DISPOSAL. DISPOSAL MUST BE IN ACCORDANCE WITH LOCAL,
STATE, AND FEDERAL REGULATIONS .
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.